Case Communications 8000 Series Specifications download pdf

Telaire Ventostat™ 8000 Series

Sensor

User Instructions

Measurement & Control

T63216-007

May 2013

Page 1 of 4

Installing the Sensor

!WARNING!

Before performing service or maintenance operations on

the systems, turn OFF main power switches to the unit.

Electric shock can cause personal injury. Please read and

follow the wiring instructions precisely; miswiring may

cause permanent damage to the product.

Basic Installation for Non-Display Units

1. Separate the case into its front and rear sections.

2. Secure the rear section of the case to the wall or junction box using

the supplied screws, and make necessary wire connections.

3. Mount the Controller on the base by aligning the top clips and then

securing to the bottom clips. Secure the Ventostat with the supplied

set screw. A one-minute stabilization warmup will take place.

Internal Label for Non-Display Units

Jumper Settings for Non-Display (a) and Display (b)

Units

Note: Example b shows outputs of CO

— 4-20 mA and CO

— 0-10

V, humidity— 4-20 mA, and active temperature — 0-5 V.

GE Measurement & Control

6860 Cortona Dr., Suite B

Goleta, CA 93117

www.ge-mcs.com

Basic Installation for Display Units

1. Separate the case into its front and rear sections.

2. Secure the rear section of the case to the wall or junction box using

the supplied screws, and make necessary wire connections.

3. Mount the Controller on the base by aligning the top clips and then

securing to the bottom clips. Secure the Ventostat with the supplied

set screw. A one-minute stabilization warmup will take place.

4. When fitting the T8300 (pitot tube version), complete the

installation by screwing the tube connectors to the input ports on the

sensor. The tubing connectors can be attached to either input port. It

will not affect the performance of the sensor. (See page 3 for further

instructions.)

Internal Label for Display Units

Output

Jumper

Selections

(a)

(b)

0-10V

0-5 V

Output

Jumper

Selections

1 2 3 4 5

Summary of Contents

Page 1 - Measurement & Control

Telaire Ventostat™ 8000 SeriesCO2 SensorUser InstructionsGEMeasurement & Control T63216-007May 2013Page 1 of 4Installing the Sensor!WARNING!Before

Page 2 - Ventostat Wiring Diagrams

Page 2 Telaire Ventostat™ 8000 SeriesVentostat Wiring DiagramsThe Ventostat family of products has two basic configurations. One configuration provide

Page 3 - Ventostat Specifications

Telaire Ventostat™ 8000 Series Page 3Sensing Duct CO2 ConcentrationsDuct-Mounting the EnclosuresVentostat products can be installed inside the return

Page 4 - Warranty/Other

Page 4 Telaire Ventostat™ 8000 SeriesPower Consumption Typical 0.7 W at nominal voltage of 24V AC RMSTemperature Dependence0.2% FS per °C (±0.11% per

Page 5

Telaire Ventostat™ 8000 Series Page 5type of equipment as specified in Table 1: Product Warranty Periods. For all warranty repairs, GE Sensing will be

Case Communications 8000 Series Specifications

Browse online or download Specifications for Networking Case Communications 8000 Series. Case Communications 8000 Series Specifications User Manual

Summary of Contents

More documents for Networking Case Communications 8000 Series

Comments to this Manuals

Case Communications 8000 Series Specifications

Browse online or download Specifications for Networking Case Communications 8000 Series. Case Communications 8000 Series Specifications User Manual

Summary of Contents

More documents for Networking Case Communications 8000 Series

Comments to this Manuals

Related products and manuals for Networking Case Communications 8000 Series